ホーム > 製品情報> 水平スラリーポンプ> ZJW給餌ポンプ> ミル粉砕給水ポンプ
ミル粉砕給水ポンプ
ミル粉砕給水ポンプ
ミル粉砕給水ポンプ
ミル粉砕給水ポンプ
ミル粉砕給水ポンプ
ミル粉砕給水ポンプ

ミル粉砕給水ポンプ

$5000≥1Set/Sets

お支払い方法の種類:L/C,T/T,Paypal,Money Gram,Western Union
インコタームズ:FOB,CFR,CIF,EXW,FAS,FCA,CPT,CIP,Express Delivery
最小注文数:1 Set/Sets
輸送方法:Ocean,Land,Air,Express,Express
ポート:Tianjin,Qingdao,Guangzhou
製品の属性

モデル65ZJW

ブランドナイプ

TypeClay Wet Sand

Casting MethodThermal Gravity Casting

Sand Core TypeClay Sand Core

ApplicationMachinery Parts

MachiningBoring Machine

MaterialSteel

Surface TreatmentSand Blast

Surface RoughnessRa0.4

StandardGB

CertificationISO 9001:2008

65ZJW Feeding Pumps65

梱包と配送
販売単位 : Set/Sets
パッケージ型式 : 木製ケース
写真の例 :
製品の説明

65のZJWフィルタープレス送りポンプ

片持ち、水平、遠心スラリーポンプ/ゴムライニングスラリーポンプ/ R55スラリーポンプ/グランドシールスラリーポンプ/遠心シールスラリーポンプ/抵抗性ゴムスラリーポンプ/交換スラリーは石炭洗浄スラリーは/ポンプ砂と砂利処理スラリーポンプ/排水処理スラリー/ポンプ着用鉱物浮選処理ポンプ/石炭洗浄ポンプ摂食/ポンプ/ポンプ


Naipu®NP-ZJWシリーズフィルタープレス供給ポンプは、独特の油圧desinとインストールモードを受け入れます

インペラは、そのポンプ性能曲線は通常ポンプよりも急峻であることを確実に使用することがより適切です

フィルタープレスフィードは、大容量を実現するために抵抗値の変化に応じて変化します

低圧供給および低容量、高圧filter.Theポンプが広く、石炭washeryで使用され

など、環境保護、アルミ工場、製錬工場



建設ドローイング

drawing-1





供給ポンプの構造チャート

1.Two相ボリュート2.Two相インペラ

3.One相渦巻4.Back板

5.Feeding部屋6.Locatingブッシュ

7.Expeller 8.Expellerカバープレート

9.Decompression体10.One相インペラ

11.Tieバー12.Shaftスリーブ

13.Cover板14.Disassemblyリング

15.Water保持プレート16.Bearing

17.Shaft 18.Bearingスペーサースリーブ

19.Bearingカバー20.Frame

21.Bentパイプ



NP-ZJW PUMPシステムチャート

selection chart



NP-ZJW供給ポンプの性能パラメータ

Performance Parameters


製品の概要:

Filter Press Photos


可能性のある障害と決済。


        Faults

    Reason

      Settlement

1.Pump fails to discharge any water,The hand of pressure gauge beat violently

1.Suction pipe don`t have enough water.

2.Suction pipe blocked or the valve is locked.

1. Inject enough water

2.unlock the inlet valve,clear the blocks

3.Exclude the air leakage

2.The pump can`t discharge water,the hand of vacuum meter beat heavily.

1.The inlet valve is unlocked or silted up.

2.The resistance of suction pipe is too big or silted up.

3.The height of suction is too high.

1.Unlock the valve or desilting

2.improve the design of  suction pipe or desilt

3.Lower the height of the installation.

3.The pump can`t discharge water,pressure gauge shows heavy pressure.

1.The resistance of the discharge pipe is too big.

2.The impeller blocked

3.The speed is slow.

1.Check and adjust the outlet pipe.

2.Clear the impeller

3. Improve the speed.

4.The pump doesn`t rotate

The volute is silted up by the blocks.

Clear the blocks

5.The capacity is not enough

1.The blocks of the impeller or the inlet or outlet pipe.

2.The abrasion of the impeller is heavily.

3.The speed is low to normal

4.Pump is installed unreasonably or the leakage of the inlet pipe.

5.The transporting height is too high,the loss of the resistance of the inside pipe are too big.

6.The inlet valve not open enough or blocked

7.The packing seal leaks

1.Clear the impeller or pipe.

2.Change the impeller

 

 

3.Adjust the speed

4.Install again or stop leaking.

 

 

5.Decrease the height of the transport or reduce the resistance.

6.Unlock the inlet valve

 

7.Compress the packing tightly

6.The motor of the pump is overloaded

1.The head of the pump exceeds the head of the working condition.

2.Not consider the slurry density when selecting the pump.

3.The packing press tightly

1.Turn down the outlet valve,cut the impeller or lower the speed.

2.Select the motor again.

3.Adjust the the screw of the  packing gland

7.Abnormal sound in the pump, and no water out

1.The resistance of the inlet pipe is too big.

2.The height of the suction is too high.

3.Cavitation occurred

4.there is air in the inlet

5.The temperature of the liquid is too high

1.Clear the suction pipe and sluice valve.

2.Lower the height of the suction

3.Adjust the water valve and let the pump operate in the defined limits.

4.Block the leakage.

5.Lowering the liquid temperature.

8.pump vibrates

1.pump cavitate

2.The block of the impeller single vane

3.The no concentricity  between the pump shaft and motor shaft

4.Fasteners or foundation loose

1.Adjust the water valve ,lower the height of the installation,reduce the resistance of the inlet.

2.Clear the impeller

3.Alignment again

4.Fasten the screw,and reinforce the foundation.

9.Bearing is overheat

1.lock the cooling water

2.lubrication is not good.

3.the lubrication oil is not clear

4.the wrong direction of the thrust bearing.

5.there is something wrong with the bearing.

1.Open the cooling water

2.Adjust the oil quantity

3.Clear the shaft,change oil

4.According to the inlet pressure,adjust the direction of the thrust bearing.

5.Change the bearing

10.Packing short life

The material of packing is not good

Change the packing

11.pump leak oil

1.High oil level

2.The rubber parts invalid  

3.Assembly problem

1.Lower the oil level

2.Change rubber spares

3.Adjust the assembly

 

12 Pump head leaking

1.The rubber parts not press well

Assembly again or press tightly 





よくある質問:

Q1。あなたは、メーカーの工場はありますか?

はい、私たちは直接製造工場であり、この分野で10年以上の経験を持っています。

Q2.Doあなたが販売する株式の製品を持っていますか?

いくつかは、我々は在庫で持っていますが、他の人ではありません。我々は常に顧客の要件に応じて、これらの製品を生産するので。

あなたはQ3.Whatの利点がありますか?

A:私たちは、直接メーカーであり、価格は競争力があります。

B:私たちのエンジニアは非常にこの領域でexperiecedされている、と私たちはあなたにOEMサービスを行うことができます。

C:私たちは、工場であり、我々はそう納期にとして、生産スケジュールを手配することができます。


連絡先の詳細:

石家荘Naipuポンプ株式会社。

追加:No.368新市北路、石家荘ハイテク産業開発区、河北省、中国、050091。

電話:0086-311-897162903

ファックス:0086-311-87162902

担当者:カレン・タン

Skype:karen_naipump











  • お問い合わせ
お問い合わせ
*
*

We will contact you immediately

Fill in more information so that we can get in touch with you faster

Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.

送信